To install click the Add extension button. That's it.

The source code for the WIKI 2 extension is being checked by specialists of the Mozilla Foundation, Google, and Apple. You could also do it yourself at any point in time.

Kelly Slayton
Congratulations on this excellent venture… what a great idea!
Alexander Grigorievskiy
I use WIKI 2 every day and almost forgot how the original Wikipedia looks like.
Live Statistics
English Articles
Improved in 24 Hours
Added in 24 Hours
Show all languages
What we do. Every page goes through several hundred of perfecting techniques; in live mode. Quite the same Wikipedia. Just better.

From Wikipedia, the free encyclopedia

Cross-section diagram of stripline geometry. Central conductor (A) is sandwiched between ground planes (B and D). Structure is supported by dielectric (C).
Cross-section diagram of stripline geometry. Central conductor (A) is sandwiched between ground planes (B and D). Structure is supported by dielectric (C).

Stripline is a transverse electromagnetic (TEM) transmission line medium invented by Robert M. Barrett of the Air Force Cambridge Research Centre in the 1950s. Stripline is the earliest form of planar transmission line.


A stripline circuit uses a flat strip of metal which is sandwiched between two parallel ground planes. The insulating material of the substrate forms a dielectric. The width of the strip, the thickness of the substrate and the relative permittivity of the substrate determine the characteristic impedance of the strip which is a transmission line. As shown in the diagram, the central conductor need not be equally spaced between the ground planes. In the general case, the dielectric material may be different above and below the central conductor.

To prevent the propagation of unwanted modes, the two ground planes must be shorted together. This is commonly achieved by a row of vias running parallel to the strip on each side.

Like coaxial cable, stripline is non-dispersive, and has no cutoff frequency. Good isolation between adjacent traces can be achieved more easily than with microstrip. Stripline provides for enhanced noise immunity against the propagation of radiated RF emissions, at the expense of slower propagation speeds when compared to microstrip lines. The effective permittivity of striplines equals the relative permittivity of the dielectric substrate because of wave propagation only in the substrate. Hence striplines have higher effective permittivity in comparison to microstrip lines, which in turn reduces wave propagation speed (see also velocity factor) according to


Stripline, now used as a generic term, was originally a proprietary brand of Airborne Instruments Laboratory Inc. (AIL). The version as produced by AIL was essentially air insulated (air stripline) with just a thin layer of dielectric material - just enough to support the conducting strip. The conductor was printed on both sides of the dielectric. The more familiar version with the space between the two plates completely filled with dielectric was originally produced by Sanders Associates who marketed it under the brand name of triplate.[1]

Stripline was initially preferred to its rival, microstrip, made by ITT. Transmission in stripline is purely TEM mode and consequently there is no dispersion (provided that the dielectric of substrate is not itself dispersive). Also, discontinuity elements on the line (gaps, stubs, posts etc) present a purely reactive impedance. This is not the case with microstrip; the differing dielectrics above and below the strip result in longitudinal non-TEM components to the wave. This results in dispersion and discontinuity elements have a resistive component causing them to radiate. In the 1950s Eugene Fubini, at the time working for AIL, jokingly suggested that a microstrip dipole would make a good antenna. This was intended to highlight the drawbacks of microstrip, but the microstrip patch antenna has become the most popular design of antenna in mobile devices.[2] Stripline remained in the ascendent for its performance advantages through the 1950s and 1960s but eventually microstrip won out, especially in mass produced items, because it was easier to assemble and the lack of an upper dielectric meant that components were easier to access and adjust. As the complexity of printed circuits increased, this convenience issue became more important until today microstrip is the dominant planar technology. Miniaturisation also leads to favouring microstrip because its disadvantages are not so severe in a miniaturised circuit. However, stripline is still chosen where operation over a wide band is required.[3]

Comparison to microstrip

Microstrip is similar to stripline transmission line except that the microstrip is not sandwiched, it is on a surface layer, above a ground plane. Stripline is more expensive to fabricate than microstrip, and because of the second groundplane, the strip widths are much narrower for a given impedance and board thickness than for microstrip.

See also


  1. ^ Oliner, pp.556-559
  2. ^ Yarman, p. 67
  3. ^ Oliner, pp. 558-562


  • Arthur A. Oliner, "The evolution of electromagnetic waveguides", in chapter 16, Sarkar et al., History of wireless, John Wiley and Sons, 2006 ISBN 0-471-71814-9.
  • Yarman, Binboga Siddik, Design of Ultra Wideband Antenna Matching Networks, Springer, 2008 ISBN 1-4020-8418-8.

External links

This page was last edited on 6 March 2019, at 18:39
Basis of this page is in Wikipedia. Text is available under the CC BY-SA 3.0 Unported License. Non-text media are available under their specified licenses. Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc. WIKI 2 is an independent company and has no affiliation with Wikimedia Foundation.