Neutron embrittlement, sometimes more broadly radiation embrittlement, is the embrittlement of various materials due to the action of neutrons. This is primarily seen in nuclear reactors, where the release of high-energy neutrons causes the long-term degradation of the reactor materials. The embrittlement is caused by the microscopic movement of atoms that are hit by the neutrons; this same action also gives rise to neutron-induced swelling causing materials to grow in size, and the Wigner effect causing energy buildup in certain materials that can lead to sudden releases of energy.
Neutron embrittlement mechanisms include:
- Hardening and dislocation pinning due to nanometer features created by irradiation
- Generation of lattice defects in collision cascades via the high-energy recoil atoms produced in the process of neutron scattering.
- Diffusion of major defects, which leads to higher amounts of solute diffusion, as well as formation of nanoscale defect-solute cluster complexes, solute clusters, and distinct phases.[1]
YouTube Encyclopedic
-
1/3Views:10 6012 436949
-
27. Nuclear Materials — Radiation Damage and Effects in Matter
-
Effects of neutron radiation on nickel-based alloys
-
Irradiation Embrittlement in 304 SS with ion irradiation
Transcription
Embrittlement in Nuclear Reactors
Neutron irradiation embrittlement limits the service life of reactor-pressure vessels (RPV) in nuclear power plants due to the degradation of reactor materials. In order to perform at high efficiency and safely contain coolant water at temperatures around 290°C and pressures of ~7 MPa (for boiling water reactors) to 14 MPa (for pressurized water reactors), the RPV must be heavy-section steel. Due to regulations, RPV failure probabilities must be very low. To achieve sufficient safety, the design of the reactor assumes large cracks and extreme loading conditions. Under such conditions, a probable failure mode is rapid, catastrophic fracture if the vessel steel is brittle. Tough RPV base metals that are typically used are A302B, A533B plates, or A508 forgings; these are quenched and tempered, low-alloy steels with primarily tempered bainitic microstructures. Over the past few decades, RPV embrittlement has been addressed by the use of tougher steels with lower trace impurity contents, the decrease of neutron flux that the vessel is subject to, and the elimination of beltline welds. However, embrittlement remains an issue for older reactors.[2]
Pressurized water reactors are more susceptible to embrittlement than boiling water reactors. This is due to PWRs sustaining more neutron impacts. To counteract this, many PWRs have a specific core design that reduces the number of neutrons hitting the vessel wall. Moreover, PWR designs must be especially mindful of embrittlement because of pressurized thermal shock, an accident scenario that occurs when cold water enters a pressurized reactor vessel, introducing large thermal stress. This thermal stress may cause fracture if the reactor vessel is sufficiently brittle.[3]
See also
References
- "Backgrounder on Reactor Pressure Vessel Issues". Nuclear Regulatory Commission. February 2016.
- Pu, Jue (18 March 2013). "Radiation Embrittlement". Stanford University.
- Specific
- ^ "Embrittlement of Nuclear Reactor Pressure Vessels". www.tms.org. Retrieved 2018-03-02.
- ^ Odette, G. R.; Lucas, G. E. (2001-07-01). "Embrittlement of nuclear reactor pressure vessels". JOM. 53 (7): 18–22. Bibcode:2001JOM....53g..18O. doi:10.1007/s11837-001-0081-0. ISSN 1047-4838. S2CID 138790714.
- ^ "Backgrounder on Reactor Pressure Vessel Issues". United States Nuclear Regulatory Commission. April 8, 2016. Retrieved March 1, 2018.
 | This nuclear physics or atomic physics–related article is a stub. You can help Wikipedia by expanding it. |
This page was last edited on 19 February 2024, at 23:02