To install click the Add extension button. That's it.

The source code for the WIKI 2 extension is being checked by specialists of the Mozilla Foundation, Google, and Apple. You could also do it yourself at any point in time.

Kelly Slayton
Congratulations on this excellent venture… what a great idea!
Alexander Grigorievskiy
I use WIKI 2 every day and almost forgot how the original Wikipedia looks like.
What we do. Every page goes through several hundred of perfecting techniques; in live mode. Quite the same Wikipedia. Just better.

Inverter (logic gate)

From Wikipedia, the free encyclopedia

Input Output
0 1
1 0
Traditional NOT Gate (Inverter) symbol
Traditional NOT Gate (Inverter) symbol

In digital logic, an inverter or NOT gate is a logic gate which implements logical negation. The truth table is shown on the right.

Electronic implementation

An inverter circuit outputs a voltage representing the opposite logic-level to its input. Its main function is to invert the input signal applied. If the applied input is low then the output becomes high and vice versa. Inverters can be constructed using a single NMOS transistor or a single PMOS transistor coupled with a resistor. Since this 'resistive-drain' approach uses only a single type of transistor, it can be fabricated at a low cost. However, because current flows through the resistor in one of the two states, the resistive-drain configuration is disadvantaged for power consumption and processing speed. Alternatively, inverters can be constructed using two complementary transistors in a CMOS configuration. This configuration greatly reduces power consumption since one of the transistors is always off in both logic states.[1] Processing speed can also be improved due to the relatively low resistance compared to the NMOS-only or PMOS-only type devices. Inverters can also be constructed with bipolar junction transistors (BJT) in either a resistor–transistor logic (RTL) or a transistor–transistor logic (TTL) configuration.

Digital electronics circuits operate at fixed voltage levels corresponding to a logical 0 or 1 (see binary). An inverter circuit serves as the basic logic gate to swap between those two voltage levels. Implementation determines the actual voltage, but common levels include (0, +5V) for TTL circuits.

Digital building block

This schematic diagram shows the arrangement of NOT gates within a standard 4049 CMOS hex inverting buffer.
This schematic diagram shows the arrangement of NOT gates within a standard 4049 CMOS hex inverting buffer.

The inverter is a basic building block in digital electronics. Multiplexers, decoders, state machines, and other sophisticated digital devices may use inverters.

The hex inverter is an integrated circuit that contains six (hexa-) inverters. For example, the 7404 TTL chip which has 14 pins and the 4049 CMOS chip which has 16 pins, 2 of which are used for power/referencing, and 12 of which are used by the inputs and outputs of the six inverters (the 4049 has 2 pins with no connection).

Analytical representation

is the analytical representation of NOT gate:


If no specific NOT gates are available, one can be made from the universal NAND or NOR gates.[2]

Desired gate NAND construction NOR construction
NOT ANSI Labelled.svg
NOT from NAND.svg
NOT from NOR.svg

Performance measurement

Voltage transfer curve for a 20 μm inverter fabricated at North Carolina State University.
Voltage transfer curve for a 20 μm inverter fabricated at North Carolina State University.

Digital inverter quality is often measured using the voltage transfer curve (VTC), which is a plot of output vs. input voltage. From such a graph, device parameters including noise tolerance, gain, and operating logic levels can be obtained.

Ideally, the VTC appears as an inverted step function – this would indicate precise switching between on and off – but in real devices, a gradual transition region exists. The VTC indicates that for low input voltage, the circuit outputs high voltage; for high input, the output tapers off towards the low level. The slope of this transition region is a measure of quality – steep (close to infinity) slopes yield precise switching.

The tolerance to noise can be measured by comparing the minimum input to the maximum output for each region of operation (on / off).

See also


  1. ^ Nair, B. Somanathan (2002). Digital electronics and logic design. PHI Learning Pvt. Ltd. p. 240. ISBN 9788120319561.
  2. ^ M. Morris, Mano; R. Kime, Charles (2004). Logic and computer design fundamentals (3 ed.). Prentice Hall. p. 73. ISBN 0133760634.

External links

This page was last edited on 5 April 2021, at 16:23
Basis of this page is in Wikipedia. Text is available under the CC BY-SA 3.0 Unported License. Non-text media are available under their specified licenses. Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc. WIKI 2 is an independent company and has no affiliation with Wikimedia Foundation.