To install click the Add extension button. That's it.

The source code for the WIKI 2 extension is being checked by specialists of the Mozilla Foundation, Google, and Apple. You could also do it yourself at any point in time.

4,5
Kelly Slayton
Congratulations on this excellent venture… what a great idea!
Alexander Grigorievskiy
I use WIKI 2 every day and almost forgot how the original Wikipedia looks like.
Live Statistics
English Articles
Improved in 24 Hours
Added in 24 Hours
What we do. Every page goes through several hundred of perfecting techniques; in live mode. Quite the same Wikipedia. Just better.
.
Leo
Newton
Brights
Milds

From Wikipedia, the free encyclopedia

Four-bolt bearing caps— Napier Deltic diesel locomotive engine
Four-bolt bearing caps— Napier Deltic diesel locomotive engine

In a piston engine, the main bearings are the bearings which hold the crankshaft in place and allow it to rotate within the engine block.

Main bearings are usually plain bearings or journal bearings, held in place by the engine block and bearing caps. The number of main bearings per engine varies between engines, often in accordance with the forces produced by the operation of the engine.

Number of main bearings

The number of main bearings is primarily determined by the overall load factor and maximum engine speed.[1] Increasing the number of bearings in an engine will generally increase the size and cost of the engine, but also reduces bending stress and deflection caused by the distance from the crank pins to the nearest bearings. The number of bearings and crank pins can also have an effect on engine balance; a more stable crankshaft will better avoid unbalance from flexing, but increasing the crankshaft length or girth to accommodate an additional bearing increases the rotational inertia of the crankshaft, which can have the opposite effect.

Most engines have at least two main bearings— one at each end of the crankshaft. Additional bearing may be located along the crankshaft, sometimes as many as one bearing per crank pin, as used on many modern diesel engines and petrol engines designed for high RPM.[1]

Some small single-cylinder engines have only one main bearing,[citation needed] in which case it must withstand the bending moment created by the offset distance from the connecting rod to the main bearing.

When describing a crankshaft design, the number of main bearings is generally quoted, as the number of crank pins is determined by the cylinder layout. For example, the Toyota VZ V6 engine is described as having a "four bearing crankshaft" and the Jaguar XK6 straight-six engine has a "seven bearing crankshaft".[2][3]

Bearing caps

The lower half of the main bearings are typically held in place by 'bearing caps' which are secured to the engine block using bolts. The basic arrangement is for each bearing cap to have two bolts, but some engines may have four or six bolts per bearing cap (often referred to as "four-bolt mains" or "six-bolt mains" engines). The additional bolts result in increased strength, allowing the engine to withstand higher power output or RPM.[4] However, the additional holes required for four- or six-bolt main bearings can increase the chance of hairline fractures developing in the engine block.[5]

The first car engine to use four-bolt main bearings was the V12 Maybach Zeppelin of 1928, that used them on three of its eight main bearings.[6]

The typical design for a six-bolt main bearing (as used by the General Motors LS engine and Ford Modular engine) is four vertical bolts (two on each side of the crankshaft) from the bottom extending into the block and two lateral cross-bolts coming from the left and right side pan rails into the side of the main caps to provide additional lateral strength.

See also

References

  1. ^ a b Bosch Automotive Handbook. Robert Bosch GmbH. 2004. p. 465. ISBN 978-0-7680-1513-3.
  2. ^ "Toyota 5VZ-FE (3.4 L, V6, DOCH) engine: review and specs, service data". www.engine-specs.net. 15 March 2019. Retrieved 29 November 2019.
  3. ^ "Best Inline Six Engines". www.hagerty.com. Retrieved 29 November 2019.
  4. ^ "Are 4 bolt main blocks stronger than 2 bolt main blocks?". www.badasscars.com. Retrieved 1 December 2019.
  5. ^ "2 vs. 4-Bolt Main? Diving Deeper Into the Myth". www.westcoastengines.com. 10 October 2018. Retrieved 1 December 2019.
  6. ^ Ludvigsen, Karl (2005). "Chapter 7: Teutonic Twelves". The V12 Engine. Sparkford, Yeovil: Haynes Publishing. p. 160. ISBN 1-84425-004-0.
This page was last edited on 1 December 2019, at 05:58
Basis of this page is in Wikipedia. Text is available under the CC BY-SA 3.0 Unported License. Non-text media are available under their specified licenses. Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc. WIKI 2 is an independent company and has no affiliation with Wikimedia Foundation.