To install click the Add extension button. That's it.

The source code for the WIKI 2 extension is being checked by specialists of the Mozilla Foundation, Google, and Apple. You could also do it yourself at any point in time.

4,5
Kelly Slayton
Congratulations on this excellent venture… what a great idea!
Alexander Grigorievskiy
I use WIKI 2 every day and almost forgot how the original Wikipedia looks like.
Live Statistics
English Articles
Improved in 24 Hours
Added in 24 Hours
What we do. Every page goes through several hundred of perfecting techniques; in live mode. Quite the same Wikipedia. Just better.
.
Leo
Newton
Brights
Milds

From Wikipedia, the free encyclopedia

Two involute gears, the left driving the right: Blue arrows show the contact forces between them. The force line (or line of action) runs along a tangent common to both base circles. (In this situation, there is no force, and no contact needed, along the opposite common tangent not shown). The involutes here are traced out in converse fashion: points (of contact) move along the stationary force-vector "string" as if it was being unwound from the left rotating base circle, and wound onto the right rotating base circle.
Two involute gears, the left driving the right: Blue arrows show the contact forces between them. The force line (or line of action) runs along a tangent common to both base circles. (In this situation, there is no force, and no contact needed, along the opposite common tangent not shown). The involutes here are traced out in converse fashion: points (of contact) move along the stationary force-vector "string" as if it was being unwound from the left rotating base circle, and wound onto the right rotating base circle.

The involute gear profile is the most commonly used system for gearing today, with cycloid gearing still used for some specialties such as clocks. In an involute gear, the profiles of the teeth are involutes of a circle. (The involute of a circle is the spiraling curve traced by the end of an imaginary taut string unwinding itself from that stationary circle called the base circle.)

The involute gear profile was a fundamental advance in machine design, since unlike with other gear systems, the tooth profile of an involute gear depends only on the number of teeth on the gear, pressure angle, and pitch. That is, a gear's profile does not depend on the gear it mates with. Thus, n and m tooth involute spur gears with a given pressure angle and pitch will mate correctly, independently of n and m. This dramatically reduces the number of shapes of gears that need to be manufactured and kept in inventory.

In involute gear design contact between a pair of gear teeth occurs at a single instantaneous point (see figure at right) where two involutes of the same spiral hand meet. Contact on the other side of the teeth is where both involutes are of the other spiral hand. Rotation of the gears causes the location of this contact point to move across the respective tooth surfaces. The tangent at any point of the curve is perpendicular to the generating line irrespective of the mounting distance of the gears. Thus the line of the force follows the generating line, and is thus tangent to the two base circles, and is known as the line of action (also called pressure line or line of contact). When this is true, the gears obey the fundamental law of gearing:[1]

The angular velocity ratio between two gears of a gearset must remain constant throughout the mesh.

This property is required for smooth transmission of power with minimal speed or torque variations as pairs of teeth go into or come out of mesh, but is not required for low-speed gearing.

Where the line of action crosses the line between the two centres it is called the pitch point of the gears, where there is no sliding contact.

The distance actually covered on the line of action is then called line of contact. The line of contact begins at the intersection between the line of action and the addendum circle of the driven gear and ends at the intersection between the line of action and the addendum circle of the driving gear.[2]

The pressure angle is the acute angle between the line of action and a normal to the line connecting the gear centers. The pressure angle of the gear varies according to the position on the involute shape, but pairs of gears must have the same pressure angle in order for the teeth to mesh properly, so specific portions of the involute must be matched.

While any pressure angle can be manufactured, the most common stock gears have a 20° pressure angle, with 14½° and 25° pressure angle gears being much less common.[3] Increasing the pressure angle increases the width of the base of the gear tooth, leading to greater strength and load carrying capacity. Decreasing the pressure angle provides lower backlash, smoother operation and less sensitivity to manufacturing errors.[4]

Most common stock gears are spur gears, with straight teeth. Most gears used in higher-strength applications are helical involute gears where the spirals of the teeth are of different hand, and the gears rotate in opposite direction.

Only used in limited situations are helical involute gears where the spirals of the teeth are of the same hand, and the spirals of the two involutes are of different 'hand' and the line of action is the external tangents to the base circles (like a normal belt drive whereas normal gears are like a crossed-belt drive), and the gears rotate in the same direction,[5] such as can be used in limited-slip differentials[clarification needed][6][7] because of their low efficiencies, and in locking differentials when the efficiencies are less than zero.

YouTube Encyclopedic

  • 1/3
    Views:
    3 733
    165 596
    118 223
  • Spur Gear Design 2 - Involute of the circle
  • Gears & Gear Manufacturing
  • Involute gears 1a

Transcription

References

  1. ^ Norton, R.L., 2006, Machine Design: An Integrated Approach, 3rd Ed, Pearson/Prentice-Hall, ISBN 0-13-148190-8
  2. ^ tec-science (2018-10-31). "Meshing of involute gears". tec-science. Retrieved 2019-10-22.
  3. ^ Juvinall, R.C. and K.M. Marshek, 2006, Fundamentals of Machine Component Design, 4th Ed, Wiley, ISBN 978-0-471-66177-1, p. 598
  4. ^ Boston Gear Company, Open Gearing Catalog, http://bostongear.com/products/open-gearing/stock-gears/spur-gears/spur-gears
  5. ^ Professor Jacques Maurel, "Paradoxical Gears", http://www.jacquesmaurel.com/gears
  6. ^ Jacques Mercier, Daniel Valentin US Patent 4831890
  7. ^ Arthur J. Fahy, Neil Gillies US Patent 5071395


gears

This page was last edited on 19 November 2020, at 09:01
Basis of this page is in Wikipedia. Text is available under the CC BY-SA 3.0 Unported License. Non-text media are available under their specified licenses. Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc. WIKI 2 is an independent company and has no affiliation with Wikimedia Foundation.