Electronic filters are circuits which perform signal processing functions, specifically to remove unwanted frequency components from the signal, to enhance wanted ones, or both. Electronic filters can be:
 passive or active
 analog or digital
 highpass, lowpass, bandpass, bandstop (bandrejection; notch), or allpass.
 discretetime (sampled) or continuoustime
 linear or nonlinear
 infinite impulse response (IIR type) or finite impulse response (FIR type)
The most common types of electronic filters are linear filters, regardless of other aspects of their design. See the article on linear filters for details on their design and analysis.
YouTube Encyclopedic

1/5Views:34 66258 36724 36694 63310 617

✪ Need and Types of Filter Circuits  Electronics  Basic Electrical Engineering  First Year Engg

✪ Lec 18  MIT 6.002 Circuits and Electronics, Spring 2007

✪ Rectifiers and Filters  Electronic Devices and Circuits

✪ Lowpass filter basics

✪ What types of filters are there? (Quick Tutorial)
Transcription
Contents
History
The oldest forms of electronic filters are passive analog linear filters, constructed using only resistors and capacitors or resistors and inductors. These are known as RC and RL singlepole filters respectively. However, these simple filters have very limited uses. Multipole LC filters provide greater control of response form, bandwidth and transition bands. The first of these filters was the constant k filter, invented by George Campbell in 1910. Campbell's filter was a ladder network based on transmission line theory. Together with improved filters by Otto Zobel and others, these filters are known as image parameter filters. A major step forward was taken by Wilhelm Cauer who founded the field of network synthesis around the time of World War II. Cauer's theory allowed filters to be constructed that precisely followed some prescribed frequency function.
Classification by technology
Passive filters
Passive implementations of linear filters are based on combinations of resistors (R), inductors (L) and capacitors (C). These types are collectively known as passive filters, because they do not depend upon an external power supply and/or they do not contain active components such as transistors.
Inductors block highfrequency signals and conduct lowfrequency signals, while capacitors do the reverse. A filter in which the signal passes through an inductor, or in which a capacitor provides a path to ground, presents less attenuation to lowfrequency signals than highfrequency signals and is therefore a lowpass filter. If the signal passes through a capacitor, or has a path to ground through an inductor, then the filter presents less attenuation to highfrequency signals than lowfrequency signals and therefore is a highpass filter. Resistors on their own have no frequencyselective properties, but are added to inductors and capacitors to determine the timeconstants of the circuit, and therefore the frequencies to which it responds.
The inductors and capacitors are the reactive elements of the filter. The number of elements determines the order of the filter. In this context, an LC tuned circuit being used in a bandpass or bandstop filter is considered a single element even though it consists of two components.
At high frequencies (above about 100 megahertz), sometimes the inductors consist of single loops or strips of sheet metal, and the capacitors consist of adjacent strips of metal. These inductive or capacitive pieces of metal are called stubs.
Single element types
The simplest passive filters, RC and RL filters, include only one reactive element, except hybrid LC filter which is characterized by inductance and capacitance integrated in one element.^{[1]}
L filter
An L filter consists of two reactive elements, one in series and one in parallel.
T and π filters
Threeelement filters can have a 'T' or 'π' topology and in either geometries, a lowpass, highpass, bandpass, or bandstop characteristic is possible. The components can be chosen symmetric or not, depending on the required frequency characteristics. The highpass T filter in the illustration, has a very low impedance at high frequencies, and a very high impedance at low frequencies. That means that it can be inserted in a transmission line, resulting in the high frequencies being passed and low frequencies being reflected. Likewise, for the illustrated lowpass π filter, the circuit can be connected to a transmission line, transmitting low frequencies and reflecting high frequencies. Using mderived filter sections with correct termination impedances, the input impedance can be reasonably constant in the pass band.^{[2]}
Multiple element types
Multiple element filters are usually constructed as a ladder network. These can be seen as a continuation of the L,T and π designs of filters. More elements are needed when it is desired to improve some parameter of the filter such as stopband rejection or slope of transition from passband to stopband.
Active filters
Active filters are implemented using a combination of passive and active (amplifying) components, and require an outside power source. Operational amplifiers are frequently used in active filter designs. These can have high Q factor, and can achieve resonance without the use of inductors. However, their upper frequency limit is limited by the bandwidth of the amplifiers.
Other filter technologies
There are many filter technologies other than lumped component electronics. These include digital filters, crystal filters, mechanical filters, surface acoustic wave (SAW) filters, bulk acoustic wave (BAW) filters, garnet filters, and atomic filters (used in atomic clocks).
The transfer function
 see also Filter (signal processing) for further analysis
The transfer function of a filter is the ratio of the output signal to that of the input signal as a function of the complex frequency :
with .
The transfer function of all linear timeinvariant filters, when constructed of discrete components, will be the ratio of two polynomials in , i.e. a rational function of . The order of the transfer function will be the highest power of encountered in either the numerator or the denominator.
Classification by topology
Electronic filters can be classified by the technology used to implement them. Filters using passive filter and active filter technology can be further classified by the particular electronic filter topology used to implement them.
Any given filter transfer function may be implemented in any electronic filter topology.
Some common circuit topologies are:
 Cauer topology – passive
 Sallen–Key topology – active
 Multiple feedback topology – active
 State variable topology – active
 Biquadratic topology – active
Classification by design methodology
Linear analog electronic filters 


Simple filters 
Historically, linear analog filter design has evolved through three major approaches. The oldest designs are simple circuits where the main design criterion was the Q factor of the circuit. This reflected the radio receiver application of filtering as Q was a measure of the frequency selectivity of a tuning circuit. From the 1920s filters began to be designed from the image point of view, mostly being driven by the requirements of telecommunications. After World War II the dominant methodology was network synthesis. The higher mathematics used originally required extensive tables of polynomial coefficient values to be published but modern computer resources have made that unnecessary.^{[3]}
Direct circuit analysis
Low order filters can be designed by directly applying basic circuit laws such as Kirchhoff's laws to obtain the transfer function. This kind of analysis is usually only carried out for simple filters of 1st or 2nd order.
Image impedance analysis
This approach analyses the filter sections from the point of view of the filter being in an infinite chain of identical sections. It has the advantages of simplicity of approach and the ability to easily extend to higher orders. It has the disadvantage that accuracy of predicted responses relies on filter terminations in the image impedance, which is usually not the case.^{[4]}
Network synthesis
The network synthesis approach starts with a required transfer function and then expresses that as a polynomial equation of the input impedance of the filter. The actual element values of the filter are obtained by continuedfraction or partialfraction expansions of this polynomial. Unlike the image method, there is no need for impedance matching networks at the terminations as the effects of the terminating resistors are included in the analysis from the start.^{[4]}
Here is an image comparing Butterworth, Chebyshev, and elliptic filters. The filters in this illustration are all fifthorder lowpass filters. The particular implementation – analog or digital, passive or active – makes no difference; their output would be the same.
As is clear from the image, elliptic filters are sharper than all the others, but they show ripples on the whole bandwidth.
See also
Notes and references
Wikimedia Commons has media related to Electronic filters. 
 ^ Dzhankhotov V., Hybrid LC filter for power electronic drives: Theory and Implementation, 2009
 ^ The American Radio Relay League, Inc.: "The ARRL Handbook, 1968" page 50
 ^ Bray, J, Innovation and the Communications Revolution, Institute of Electrical Engineers
 ^ ^{a} ^{b} Matthaei, Young, Jones Microwave Filters, ImpedanceMatching Networks, and Coupling Structures McGrawHill 1964
 Zverev, Anatol, I (1969). Handbook of Filter Synthesis. John Wiley & Sons. ISBN 0471986801.CS1 maint: Multiple names: authors list (link) Catalog of passive filter types and component values. The Bible for practical electronic filter design.
 Williams, Arthur B; Taylor, Fred J (1995). Electronic Filter Design Handbook. McGrawHill. ISBN 0070704414.
External links
 National Semiconductor AN779 (TI SNOA224a) application note describing analog filter theory
 Fundamentals of Electrical Engineering and Electronics – Detailed explanation of all types of filters
 BAW filters (in French; PDF)
 Some Interesting Filter Design Configurations & Transformations
 Analog Filters for Data Conversion