The Barcol hardness test characterizes the indentation hardness of materials through the depth of penetration of an indentor, loaded on a material sample and compared to the penetration in a reference material. The method is most often used for composite materials such as reinforced thermosetting resins or to determine how much a resin or plastic has cured. The test complements the measurement of glass transition temperature, as an indirect measure of the degree of cure of a composite. It is inexpensive and quick, and provides information on the cure throughout a part.[1]
YouTube Encyclopedic
-
1/3Views:14 32240 164588
-
Rockwell-Hardness-check-calibration-3.f4v
-
Rockwell Hardness Testers Video
-
Wood Finish Quality Control - Rocker Hardness Test
Transcription
Barcol impressor
Originally called the Barber-Colman Impressor, the Barcol impressor was developed by Walter Colman as a hand-held, portable means of assessing the hardness of a material during World War II.[2] The United States Army Air Corps required a hand-held method of checking the hardness of rivets due to concerns that aircraft could be sabotaged by replacing normal rivets with soft lead or wooden ones which would fail during flight.[3] The impressor operates when the tip is pressed against the material in question.[3] The hardness of the material determines how far the tip indents and this is transferred by a tension spring and lever to be read on a dial.[3]
Operation
The Barcol hardness test is generally used on soft materials such as rigid plastics. It measures hardness based on indentation of a sharp point with a flat tip. The test is performed using a similar method and indentation device as that used to measure Shore D hardness, however the Shore D indentor has a round tip.[4] Barcol hardness is not a valid hardness measure for curved surfaces.[5]
Scales and values
The governing standard for the Barcol hardness test is ASTM D 2583.[4] Barcol hardness is measured on a scale from 0 to 100 with the typical range being between 50B and 90B. A measurement of 60B is roughly equivalent to a Shore hardness of 80D or a Rockwell hardness M100.[4][6] As defined in ASTM D 2583 the scale divisions from 0-100 should each indicate a depth of 0.0076 mm or the equivalent 0.0003 inches.[7]
See also
- Brinell hardness test
- Knoop hardness test
- Rockwell scale
- Shore durometer
- Vickers hardness test
- Hardness comparison
References
- ^ "A model specification for FRP composites for civil engineering structures.(fiber reinforced polymer composite materials)". Construction and Building Materials. 2003-09-01. Retrieved 2008-06-15.
- ^ "The Barcol Impressor". Archived from the original on 22 June 2008. Retrieved 2008-06-15.
- ^ a b c Bennett, Robert B (September 1967). "Impressor Impresses Industry". Barber-Colman News. Retrieved 2008-06-15.
- ^ a b c Harper, Charles A.; Petrie, Edward M. (10 October 2003). "Barcol Hardness". Plastics Materials and Processes: A Concise Encyclopedia. John Wiley and Sons. ISBN 9780471459200. Retrieved 2008-02-10.
- ^ "NHML Resources - Hardness Testing". New Hampshire Materials Laboratory, Inc. Archived from the original on 12 May 2008. Retrieved 2008-06-21.
- ^ "Appendix I: Charts and Tables". Handbook of Plastics Testing and Failure Analysis: 560–617. 2007. doi:10.1002/9780470100424.app9. ISBN 9780470100424.
- ^ ASTM D 2583-07 "Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor". ASTM International. Revision as of 2007-03-01
This page was last edited on 12 January 2023, at 07:42